Guitar Fuzz Effects Pedal Kit

This kit is based on the legendary fuzz face pedal. Instead of ultra rare germanium transistors, it uses genuine new old stock NKT128 Newmarket vintage PNP germanium transistors to give you that classic germanium fuzz, while keeping the cost down. This project is ideal if you're looking to get into guitar pedal building.

The v2 includes an indicator LED and a footswitch daughterboard to make assembly easier and cleaner.
 

The following components are included in this kit:

• Instructions  x 1
• 100kΩ 1/4W carbon resistor x 1
• 33kΩ 1/4W carbon resistor x 1
• 470Ω 1/4W carbon resistor x 1
• 4.7kΩ 1/4W carbon resistor x 1
• 1MΩ 1/4W carbon resistor x 1
• 2.2kΩ 1/4W carbon resistor x 1
• 2.2µF 25V electrolytic capacitor x 1
• 22µF 25V electrolytic capacitor x 1
• 10nF dipped polyester capacitor x 1
• 220µF 25V electrolytic capacitor x 1
• 100nF boxpoly capacitor x 1
• 1N4007 diode x 1
• 1kΩ 9mm vertical potentiometer x 1
• 500kΩ 9mm vertical potentiometer x 1
• 10kΩ 10mm horizontal trimpot x 1
• 5mm red LED x 1
• LED Spacer x 1
• NKT128 Germanium PNP BJT x 2
• 6.3mm (1/4") stereo chassis socket x 1
• 6.3mm (1/4") mono chassis socket x 1
• 2.1 x 5.5mm switched DC chassis socket x 1
• PP3 battery snap x 1
• PCB x 1
• Footswitch x 1
• Footswitch daughterboard PCB x 1
• Hookup wire x 50cm

To assemble this kit, you will need the following tools:

• Soldering iron and solder
• Side cutters
• Track cutter
• Drill (only needed if you want to drill an enclosure)

IC Dual Low Noise Operational Amplifier 8DIL (Same as TL072CP/CN).

High quality AB Elektronik 4 Watt wirewound potentiometer 50 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

High quality AB Elektronik 4 Watt wirewound potentiometer 25 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

14 Watt 5% Wire-wound Resistor 22 ohms

Velcro Cable Tie Black 5m Roll Cut to Size

High quality Tyco 1 Watt wirewound potentiometer 10 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

High quality Bourns 2 Watt multi-turn wirewound potentiometer 50 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

High quality Vishay 2 Watt multi-turn wirewound potentiometer 100 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

High quality Spectrol 2 Watt multi-turn wirewound potentiometer 100 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

High quality TT Electronics 5 Watt multi-turn wirewound potentiometer 10 ohms

Ideal for loudspeaker volume controls, speed controllers, etc.

HDMI Extender via CAT5E or CAT6E Cable up to 50 metres 

• Extends HDMI signals to up to 60 metres (cat5e - 50m)
• Amplifies the HDMI signal and sends via CAT5 or CAT6 cable
• Supports HDTV at a resolution of up to 1080p
• 3D Enabled
• Copy EDID for 3D stereo
• Easy to install and use
• Complete with plug in UK power adaptors

Power supply to use with the transmitter or the receiver. Only one power supply needed. 

2.4" inch SPI LCD 240 x 320 65K Colour Display

Type: IPS LCD

Driver chip: ST7789V

Dimensions: 47x71x13.5mm

Supply voltage: 3.3V DC

 

Rubber Drive Belt Square Section, Thickness: 2mm Inside Diameter 37mm

Matrix Board. 0.1 inch (2.54mm) spacing with Double Sided Padded Holes

They are not connected to each other. 

You can connect with wires or jumpers. 594 holes. 60 x 80mm. Rows and Columns marked for easy identification

Matrix Board. 0.1 inch (2.54mm) spacing with Double Sided Padded Holes

They are not connected to each other. 

You can connect with wires or jumpers. 432 holes. 50 x 70mm. Rows and Columns marked for easy identification

Matrix Board. 0.1 inch (2.54mm) spacing with Double Sided Padded Holes

They are not connected to each other. 

You can connect with wires or jumpers. 240 holes. 30 x 70mm. Rows and Columns marked for easy identification

Diode WE Microwave 12KV 450mA

Will Replace CL01-12 and many other microwave diodes

12V UPS Uninterruptible Power Supply 15W 3A 

This UPS makes a great add on to any project that you want to add an always on level of safety. It also works great for a project you want to run off a rechargeable battery or USB, this UPS has everything built in so you don't need to use a USB charging PCB, a boost converter, a BMS and a battery holder.

• Automatic seamless switching to battery power in case of power failure
• Over charge battery protection
• Over discharge battery protection,
• Overtemperature battery protection
• Overcurrent battery protection
• Battery status Led

UPS output: Terminals marked UPS+ (positive)  and UPS- (ground))

Use with USB power OR external power input (Terminals marked 5V+ (positive) and 5V- (ground))

Use with 1 or 2 x 18650 batteries or with external 3.7V lithium batteries 

Available also with 5V and 9V output

5V UPS Uninterruptible Power Supply 15W 3A 

This UPS makes a great add on to any project that you want to add an always on level of safety. It also works great for a project you want to run off a rechargeable battery or USB, this UPS has everything built in so you don't need to use a USB charging PCB, a boost converter, a BMS and a battery holder.

• Automatic seamless switching to battery power in case of power failure
• Over charge battery protection
• Over discharge battery protection,
• Overtemperature battery protection
• Overcurrent battery protection
• Battery status Led

UPS output: Terminals marked UPS+ (positive)  and UPS- (ground))

Use with USB power OR external power input (Terminals marked 5V+ (positive) and 5V- (ground))

Use with 1 or 2 x 18650 batteries or with external 3.7V lithium batteries 

Available also with 9V and 12V output

9V UPS Uninterruptible Power Supply 15W 3A 

This UPS makes a great add on to any project that you want to add an always on level of safety. It also works great for a project you want to run off a rechargeable battery or USB, this UPS has everything built in so you don't need to use a USB charging PCB, a boost converter, a BMS and a battery holder.

• Automatic seamless switching to battery power in case of power failure
• Over charge battery protection
• Over discharge battery protection,
• Overtemperature battery protection
• Overcurrent battery protection
• Battery status Led

UPS output: Terminals marked UPS+ (positive)  and UPS- (ground))

Use with USB power OR external power input (Terminals marked 5V+ (positive) and 5V- (ground))

Use with 1 or 2 x 18650 batteries or with external 3.7V lithium batteries 

Available also with 5V and 12V output

HiFi Wired Headphones

These incredible wired headphones are great for listening to your music while out and about, with a built in microphone you can make and receive calls without taking your phone out. The microphone also doubles as a remote for your phone allowing you to adjust the volume as well as skip and pause. These in ear earphones are one of the best bang for buck earphones around, reviewed and recommended by experts and casual listeners alike. 

• Built-in microphone for hands free calls
• Driver: 15.4mm dynamic driver
• Diaphragm: PPS
• Frequency Response: 20 - 20,000Hz
• Sensitivity: 115±3dB
• Impedance: 32Ω

5.0V 1A Positive Low Drop Out Voltage Regulator SOT-223 (Surface Mount)

Suitable for repairing Arduino boards.

Raspberry Pi Pico RP2040 development board

 Dimensions : 54mm x 22mm

Documentation

Waterproof RJ45 (8P8C) coupler. Joins 2 leads with RJ45 plugs

Both sides accept 8P8C plugs.

IP67 Rated

Heatsink for TO218/TO247/T0220/TO126 and other flat packages.

Black anodised 11.4 degC/W.

Dimensions: 34 x 25 x 13mm

Wire holder for soldering

Many other useful applications.

Mains In-Line Through-Switch 250VAC 6 Amps Max Slim

Made from heat resistant plastic

Two Pole connection

Automatic Centre Hole Puncher

• Precise Punch
• Adjustable spring tension
• Ergonomic design
  

Clear Contact Adhesive 50ml