Search Results

IC MCU 1K EEPROM 36 RAM 10MHz 18DIL

6.5cm High Frequency Piezo Horn Driver 150W Max
For use with reflector horns fitted with 1.375" (1 3/8") thread.

Crossover or capacitor not needed, due to high frequency only response.
Recommended to use a 10W protection resistor in series, around 33 ohms

Frequency response: 3,000Hz to 30,000Hz

Impedance: 1000 ohms @ 1,000Hz

Power max: 150W

SPL @ 1W/1m: 93dB

Dimensions: 75 x 65mm

Weight 95g

Piezo Tweeter
High efficiency piezo-electric high impedance tweeter that doesn't need a cross-over capacitor.

Clean & crisp reproduction of  high frequencies. Can be used in series with 10W 33ohm resistor for protection, but will work perfectly without.

Power max: 150W
Frequency response: 4kHz - 30kHz
Impedance @ 1kHz: 1k ohms
Impedance @ 25kHz: 60 - 80 ohms
Dimensions: 85 x 85 x 70mm

Piezo Horn Tweeter

Special piezo high impedance tweeter featuring high efficiency without overloading the amplifier.

Connect easily via a series resistor of around 33 ohms 10 Watts. No need for a capacitor.

Crisp, clean reproduction of the high frequencies.

• Power max.150W
• Frequency response4kHz - 30kHz
• Impedance : 1kHz1k ohms
• Impedance : 25kHz
• Dimensions: 145mm x 68mm

High Definition 2.MP 1080P Camera Inside a innocent looking dummy PIR Housing with Invisible Night Vision IR LEDs (no red glow) 

High quality 2.1MP 1080P High Definition 4in1 (AHD,TVI,CVI and CVBS) camera in a PIR housing.

Fitted with 940nm IR LEDs that are totally invisible with no red glow. Ideal for surveillance in indoor areas without arousing suspicion.

Athough this is a high definition camera, we can set it for older 720P or non-HD older DVRs if you contact us on 020 8452 0161.

Specifications:

Image Sensor: 1/2.9" Sony Exmor IMX323 CMOS Sensor
DSP: Fulham FH8536E
Resolution: 2.0 Megapixel, 1920(H)×1080(V) 1080P
Lux: 0.01 (0 Lux with IR on)
Lens: Fixed 3.7mm Pinhole with IR Cut
Power Requirements: 12VDC 1Amp max.
Noise Reduction: 2D & 3D
Shutter: 1/50-1/100,000
Infra-red Source: 49pcs 960NM (Invisible to the human eye) IR LEDs
Terminations: Flying Leads with BNC (Video) & DC (Power) Sockets
Operating Temperature: -10 to +55 C
Size: W69mm x H118mm x D47mm

PIR sensor module for Arduino and other microcontroller projects

Adaptor: PL259 (UHF) Socket (Female) to BNC Plug

UHF Male (PL259) to BNC Female.

High Quality UHF Plug with 10mm cable entry

Accepts RG213 cable for example.

Solder centre pin and twist/hold screen by screw-thread

UHF Plug with 6mm cable entry. for example RG6 cable.

Solder centre pin and twist/hold screen by screw-thread

3mm LED Plastic Bezel - Sanp in

DC Chassis Plastic Switched Socket for plugs 2.1mm x 5.5mm 

(To fit our part numbers ROCA & ROCB)

5mm Plastic LED Bezel - Ring & Retaining Clip.

IC Phase Locked Loop 16DIL

Energy Efficient UK Switch-mode Variable Voltage Universal Power Supply 1500mA

 Plug in Power Supply with Various Tips & Voltages:: 3V, 4.5V,  6V, 7.5V, 9V & 12V all at full rated output of 1500mA
 

• Energy Efficient
• Short circuit protection
• Overheating protection
• Overload protection
• Overcurrent protection

All voltages are regulated & selected by a small rotary switch:

UK mains plug. Can operate from 100VAC to 240VAC 50/60Hz

Adaptor plugs    3.5mm jack, 2.35 x 0.75mm, 3.5 x 1.35mm, 4 x 1.7mm, 5 x 2.1mm, 5.5 x 2.1mm, 5.5 x 2.5mm, 6.3 x 3mm

UK Approvals

Cable length 1.8m

Full UK  & EU Approvals

CE, Haus, Quader, WEEE, BS1363

NPN TO92 EBC 30V 600mA 250MHz

PNP TO92EBC Please go to equivalent  MPS2907A

Standard "Chicken head" Pointer Knob for 6.3mm (¼ inch knob)

• Heat-resistant plastic

• Grub screw fixing

• Diameter 19mm

• Suitable for 6.35mm (0.25in) ¼" spindles

Polyimide Film Tape 15mm x 27m

This polyimide film tape is stable across a wide range of temperatures (-70°C to 280°C).


Specifications:

Width: 15mm
Length: 27m
Thickness: 0.055mm
Tensile Force: ≥ 42N/25mm
Peeling Force: ≥ 26N/25mm

Polyimide Film Tape 25mm x 27m

This polyimide film tape is stable across a wide range of temperatures (-70°C to 280°C).


Specifications:

Width: 25mm
Length: 27m
Thickness: 0.055mm
Tensile Force: ≥ 42N/25mm
Peeling Force: ≥ 26N/25mm

High Quality Plug in Power Adaptor, Power Supply with 8 tips 3, 4.5, 6, 7.5, 9, 12V at 1000mA

Energy Efficient. Short circuit Protection, Overheating Protection, Overloading Protection & Overcurrent Protection

All voltages are regulated & selected by a small rotary switch:

Voltages: 3V, 4.5V,  6V, 7.5V, 9V & 12V all at full rated output of 1000mA

UK mains plug. Can operate from 100VAC to 240VAC 50/60Hz
Adaptor plugs    3.5mm jack, 2.35 x 0.75mm, 3.5 x 1.35mm, 4 x 1.7mm, 5 x 2.1mm, 5.5 x 2.1mm, 5.5 x 2.5mm, 6.3 x 3mm

Cable length 1.8m

Full UK  & EU Approvals

CE, Haus, Quader, WEEE, BS1363

PP3 9V Battery. High Quality Long Life Alkaline Battery

Last up to 6 times longer than normal zinc carbon cells. Price and quality similar to Duracell

Strong Solid Plastic PP3 9 Volt  Battery Snaps.

100mm long lead with molded centre-positive 2.1 x 5.5mm DC connector. Great for powering Arduino or other similar boards off a battery. 

Fits 6LF22, LS9V, GP1604G-C1, 6LR6, MN1604, 6LP3146, 1604AU, CRV9, KF00492, 6LR61 and many more  batteries

Strong Solid Plastic PP3 9 Volt  Battery Snaps.

With 150mm Red & Black PVC covered wires emerging at one end.

Fits 6LF22, LS9V, GP1604G-C1, 6LR6, MN1604, 6LP3146, 1604AU, CRV9, KF00492, 6LR61 and many more  batteries

Strong Solid Plastic PP3 9 Volt  Battery Snaps.

With 150mm Red & Black PVC covered wires emerging at the center.

Fits 6LF22, LS9V, GP1604G-C1, 6LR6, MN1604, 6LP3146, 1604AU, CRV9, KF00492, 6LR61 and many more  batteries

PP3 Battery Holder with solderable PCB pins & 3 mounting holes.

54 x 30 x 21mm

PP9 Battery Snaps. One piece. Leads 100mm min long

Fits Large 9 Volt PP9 battery (not to be confused with smaller PP3 9V battery).

 Comprehensive Pro-Audio Cable Tester for XLR, Speakon, Jacks, DIN, Banana, Phono RCA, RJ45 etc